Streaming help · Streamlabs

Add or Remove Streamlabs Destinations While Staying Live

Set up Live Output Editing before the broadcast, then change one destination and verify the remaining streams.

START HERE

Enable Live Output Editing in the Go Live window before starting an Ultra stream. During the broadcast, use Manage Stream to change destination toggles and apply the update. An existing session started without this feature needs a restart before it can use it.

No unintended destination remains broadcasting after the session.

In this guide
Before you start
  • Streamlabs Ultra and a current Streamlabs Desktop build.
  • Connected destination accounts with permission to stream.
  • A planned test broadcast and each destination's viewer page.

Identify the result you need

Changing a destination is different from changing scenes. A scene switch changes the programme sent to the current outputs; Live Output Editing changes which outputs receive it. Write down the intended start and stop time for each platform before opening the live controls. This avoids disconnecting the wrong audience during a busy segment.

Streamlabs documents two important boundaries: Live Output Editing cannot run with Stream Shift, and a session consisting only of vertical destinations is unsupported. For mixed orientations, enable Dual Output before the initial start. These are session prerequisites, so a missing control is not automatically an account-linking fault.

Work through the setup

  1. Prepare the destination list

    In Go Live, confirm the account and orientation beside every destination. Enable Live Output Editing, choose the initial destinations and start the planned broadcast. Leave a screenshot of the destination names without showing any keys.

    Look for: The initial platforms show the intended programme, and Manage Stream is available.

  2. Add one destination

    Open Manage Stream, enable the additional destination and apply Update. Keep the original destination's viewer page open while the new platform connects.

    Look for: The added platform receives the stream while the original continues. A dashboard toggle alone is insufficient proof.

  3. Remove only the finished destination

    Return to Manage Stream, disable the platform whose segment has ended and apply Update. Announce the end on that platform before the change.

    Look for: The selected platform stops receiving the broadcast; destinations left enabled continue.

  4. Verify the final stop

    At the end, use the broadcast stop control and check every platform page. Record any platform that stayed live or produced a separate replay.

    Look for: No unintended destination remains broadcasting after the session.

Check the actual result

Use a visible harmless cue, such as holding up three fingers, to compare the viewer pages. Their delays can differ, so do not interpret a few seconds of old footage as a disconnect. Check that fresh motion and sound eventually arrive on every active destination.

Keep a small destination log: requested change, time applied and observed result. If one platform fails, this separates an account-specific connection problem from a failure of the entire Streamlabs session. Do not rotate every platform key merely because one output did not start.

Make the next session predictable

If you depend on a desktop-to-phone handoff, choose Stream Shift for that session and plan destinations beforehand. The documented incompatibility is a production decision to make before viewers arrive.

After a successful test, retain the exact orientation and destination arrangement for the real event. Adding several new platforms and changing the programme layout simultaneously makes a failed rehearsal difficult to diagnose.

Still stuck?

Manage Stream cannot edit outputs

Confirm Ultra access and whether Live Output Editing was enabled before starting. If it was not, schedule a clean stop and restart; it cannot be retrofitted into that session.

A new platform stays offline

Open that destination directly, check streaming eligibility and account identity, then test its connection separately. Keep working destinations running if their output is healthy.

Try it on your own setup

Start small: try the free files or continue with a guide for the part you’re working on.

Add a PNG or Overlay to Streamlabs: Image or Media? ↗

Sources & references

Documentary review of current first-party help pages and indexed first-party excerpts, checked November 4, 2026. The diagnostic sequence and rehearsal examples are original editorial guidance; Foxdip did not operate a private account, run these broadcasts or measure performance. Expected results are checks for the reader to perform, not claimed test results.

  1. Streamlabs — Live Output Editing ↗Checked 2026-11-04

Spotted something out of date? Let Alex know.

How we put our guides together ↗
READ NEXT

A few places to go from here.

All stories

Add a PNG or Overlay to Streamlabs: Image or Media?

Your PNG won't show up in Import Overlay? Add still images as an Image source and videos as a Media source. Here's which file goes where, step by step.

Run an Unlisted YouTube Test Stream Before Going Public

Create a separate unlisted rehearsal and check your real watch page, audio, scenes and ending procedure.