OBS Studio · Practical guide

Build an OBS Image Slideshow That Resumes the Way You Expect

Choose slide order, timing and hidden-scene behavior, then rehearse leaving and returning to the slideshow before using it on stream.

START HERE

Add an Image Slide Show source, select its image list and playback mode, and deliberately choose what happens while it is hidden. Test both the last slide and a return to the scene.

Choose slide order, timing and hidden-scene behavior, then rehearse leaving and returning to the slideshow before using it on stream.

In this guide
Before you start
  • A small set of images you have permission to display.
  • An OBS test scene and a second scene for the visibility check.

Decide whether the sequence is a presentation or a loop

A timed starting screen and a narrated photo presentation have different requirements. One can advance automatically while the other must wait for the speaker. Decide whether order matters, whether the sequence should repeat, and what the viewer should see after the final image.

OBS’s Image Slide Show supports lists of files or directories, manual or automatic progression, transitions, looping and hidden-source behavior. Keep the first test to three clearly numbered images. A small sequence makes an unexpected skip or restart much easier to identify.

Prepare images as one coherent visual set

Use consistent dimensions or an intentional fitting strategy so each image occupies a predictable area. Inspect text and important faces near the edges. A source-sized box alone does not establish that every differently shaped image is presented usefully.

Put the chosen files in a stable folder and keep their order obvious. If you load a directory, review its contents before the session so an unrelated image is not included accidentally. For a controlled presentation, an explicit list can make the intended sequence easier to audit.

Configure a short, observable sequence

  1. Create the list and mode

    Add Image Slide Show, select the three test images and choose automatic or manual progression according to the job. Disable randomization when order matters.

    Look for: The first pass follows the planned image sequence.

  2. Choose timing and the ending

    Set a readable interval and transition, then decide whether to loop or finish. Watch the last image and the behavior immediately afterward.

    Look for: The sequence does not unexpectedly restart or leave an unsuitable final frame.

  3. Test a scene departure

    Choose the intended Visibility Behaviour, leave for the second scene mid-sequence, wait briefly and return. Record the result.

    Look for: The slideshow continues, pauses or restarts according to the behavior you deliberately selected.

Judge time by reading, not by the slider alone

Read the densest slide aloud while watching the recording. Include the transition time in your impression of how long its content is comfortably visible. A setting that works for one photograph may be too quick for a card containing names, dates and instructions.

For manual progression, rehearse the advancing control from the same application focus you will use during the presentation. If the speaker also controls slides, make sure they can recover from one accidental advance without disrupting the narration. Keep a stable holding image available.

Test the event’s real interruptions

Leave the slideshow for a camera scene, return after a short announcement and let the sequence reach its end. These are common moments for a hidden-source setting to surprise an operator. A successful uninterrupted loop does not verify the return behavior.

Before the actual session, inspect the final file list, the longest slide and the end state again. After moving the assets, verify their paths. Save the chosen playback policy in the scene notes so a later editor does not change continue to restart without realizing how the presentation uses it.

Still stuck?

The slideshow returns on an unexpected image.

Inspect Visibility Behaviour and test departure midway through a numbered three-image sequence.

Keep troubleshooting

Check the model and connection before trying another change. The device page gathers the related symptoms.

More help with OBS Studio ↗

Sources & references

Based on the linked first-party OBS documentation checked on 4 November 2026. The exercises and acceptance checks are editorial workflows for you to run; no hands-on OBS session or hardware benchmark is claimed.

  1. OBS — Image Sources ↗Checked 2026-11-04

Spotted something out of date? Let Alex know.

How we put our guides together ↗
READ NEXT

A few places to go from here.

All stories

OBS Says "Media Source Is Not Playable"? Here's the Fix

Seeing "media source is not playable" in OBS? It usually means OBS can't open that file. Here's how to find out why and get your video playing.

Stream Layout Readability: Can Viewers See What Matters?

Check your webcam, text and overlays in a small player. Keep game information visible and give each scene a clear focus.