Practical hardware guide

Elgato Studio EDID: choose Merged, Internal or Display

Choose an EDID mode for a console or dual-PC capture chain, then test the source, passthrough display and recording separately.

START HERE

Start with Merged for a normal console-to-capture-card-to-monitor chain. Internal suits a capture input without a passthrough display. Display is a diagnostic option when Merged causes display problems, but it can advertise modes the capture card cannot record.

A repeatable input format that works both on the play display and in a local recording.

In this guide
Before you start
  • A supported Elgato capture device and current Elgato Studio software.
  • The source and monitor manuals, plus a record of the currently working signal format.

Before you change the setup

EDID tells the source which video and audio formats the receiving chain advertises. Changing it can change the choices offered by a console or graphics driver. It does not add bandwidth to a cable, improve a capture card's hardware limits or repair a loose connector. Use this guide after the direct source-to-display connection already works.

Elgato now documents these controls in Elgato Studio; the older 4K Capture Utility EDID page is marked legacy. Open the upper-right expander, choose Device and find Input EDID Mode. Record the original selection before changing anything so that the working configuration remains easy to restore.

Run a controlled check

  1. Write down the whole chain

    Record source output resolution, refresh rate and HDR state, capture model, display model and whether HDMI OUT is actually used. Photograph cable labels if several similar devices sit under the desk.

    Look for: You have a baseline that explains the topology instead of a list of settings copied from somebody else's setup.

  2. Choose the mode for that topology

    For a connected passthrough display, begin with Merged. For an input-only dual-PC chain, examine Internal and select a preset that matches the intended source format. Reserve Display for a controlled comparison when the monitor misbehaves under Merged.

    Look for: The selected mode has a specific purpose. The source can offer a different set of formats after the change.

  3. Recheck the source output

    After the HDMI connection renegotiates, inspect the source settings again. Select a format supported by the source, capture card and connected display. Do not assume an earlier 144 Hz or HDR choice survived unchanged.

    Look for: The source reports the format you actually intend to send, rather than an automatically chosen fallback.

  4. Test both destinations

    Watch the play display and record a short moving scene with audio. Replay the saved file, then repeat the reconnect or restart that originally triggered the issue.

    Look for: Both destinations remain usable after a normal start-up. A picture on the monitor alone is not a completed capture test.

Read the result and keep a working setup

If Display restores the monitor while capture becomes black, the display's advertised capabilities may exceed capture support. Return to the known-good mode and lower the source format before trying again. If Internal breaks only the passthrough display, its preset may include a mode the monitor cannot accept. Those outcomes narrow the problem more than repeatedly reinstalling recording software.

A custom EDID file is an advanced compatibility intervention, not the next routine step. Keep the original configuration, use a manufacturer-supported preset first and send support the exact chain plus the before/after signal formats if no supported combination works. For a reliable desk setup, keep a short note of the chosen mode alongside the cable map; revisit it when the display, GPU or capture hardware changes.

Keep these distinctions clear

Keep these distinctions clear
ObservationUseful next comparison
No direct source-to-monitor pictureResolve the source or HDMI path first.
Monitor works; capture fails after Display modeCompare a lower supported source format.
Only input is connectedCheck an appropriate Internal preset.

Try it on your own setup

Start small: try the free files or continue with a guide for the part you’re working on.

Elgato HD60 X Shows No Signal: Follow the HDMI Path ↗

Sources & references

Documentation review checked 4 November 2026 using the primary sources listed below. This is not a hands-on product test: the diagnostic sequence and rehearsal suggestions are Foxdip editorial guidance. No measured performance, search volume, price or universal compatibility result is claimed.

  1. Elgato Studio Software — EDID Settings ↗Checked 2026-11-04
  2. 4K Capture Utility — EDID Configuration (legacy) ↗Checked 2026-11-04

Spotted something out of date? Let Alex know.

How we put our guides together ↗
READ NEXT

A few places to go from here.

All stories

Elgato HD60 X Shows No Signal: Follow the HDMI Path

Find whether HD60 X loses the console signal, the passthrough picture or the USB preview, then test one connection at a time.

4K Passthrough or 4K Recording? Read the Capture Card Spec

Separate the HDMI display path from the USB recording path, then read resolution, frame rate, HDR and host bandwidth as one supported combination.