Configure onboard recording on each transmitter in RØDE Central and confirm the REC state with a short test. Export and open that test file before relying on the backup. A receiver meter or a live stream alone does not prove a transmitter recording exists.
A recoverable recording from each transmitter, with a clear naming and export procedure.
In this guide
Before you start
- Wireless GO II transmitters, RØDE Central and an appropriate USB data cable.
- A computer with storage for exported recordings and a local editing/playback application.
Before you change the setup
A wireless link and an onboard recording are separate deliverables. The live receiver can work while a recording mode is not configured as expected, and an onboard file may exist even when the live link has a problem. Test the backup as an independent workflow before a session that cannot be repeated.
RØDE documents Always, Backup and Button recording modes for Wireless GO II. Their start conditions differ. The support guidance also says firmware updates and factory resets restore default settings, which makes a fresh verification worthwhile after those changes. Do not assume a previous successful session permanently establishes the current state.
Run a controlled check
Choose the intended start condition
Connect each transmitter to RØDE Central and inspect its onboard recording setting. Choose the documented mode that fits the session, then label the transmitter so its files can be associated with the correct speaker.
Look for: Every transmitter has an intentional recording mode rather than an unverified default.
Make a short identifiable take
Start the devices as you would for real use. Speak the transmitter name and a short phrase, then confirm the documented REC indication. Stop the test using the chosen mode's normal behavior.
Look for: You have a small test that can be recognized later without opening many anonymous files.
Export the test
Connect the transmitter and use Central's export workflow. Choose an editable format such as WAV for an editing/archive copy and save it to a clearly named session folder.
Look for: The recording becomes an accessible file outside the transmitter, which is necessary for actual recovery.
Open and inspect the exported file
Play the beginning, middle and end, verify the correct speaker and check the duration. If it will replace camera audio, make a simple synchronization test in the editor using a visible/audible marker recorded at the start.
Look for: The backup is usable in your real post-production workflow, not merely listed in a device manager.
Repeat for both transmitters
Export each speaker's test separately and keep their naming distinct. After a real session, verify the exported copies before clearing device storage. Preserve original files until the edited result is checked.
Look for: A two-person session has two identifiable recoverable sources without a premature deletion step.
Read the result and keep a working setup
A file exported at a different bit-depth setting does not retroactively change how the original audio was captured or restore every overloaded signal. Use export options for compatibility and editing needs rather than as a promise of repaired audio. Keep a clean source recording as the first priority.
The mode named Backup has a documented relationship to transmission to the receiver; Always has a different start condition. Rehearse the actual power sequence and breaks you plan to use. That is more useful than assuming either label covers every possible failure or every moment the person is wearing the transmitter.
Obtain the participants' agreement to recording and use a visible session routine so nobody mistakes a muted live channel for a guarantee that no onboard recording is running. The practical checklist is small: configured mode, REC check, identifiable test, verified export. No runtime or storage-capacity benchmark is claimed here, and you should check available device storage before long sessions.
Keep these distinctions clear
| Evidence | What it proves |
|---|---|
| Receiver audio meter | Live audio reaches the receiver. |
| REC indication | Onboard recording is active as documented. |
| Opened exported file | The take is recoverable in your workflow. |
Sources & references
Documentation review checked 4 November 2026 using the primary sources listed below. This is not a hands-on product test: the diagnostic sequence and rehearsal suggestions are Foxdip editorial guidance. No measured performance, search volume, price or universal compatibility result is claimed.
- RØDE — Enable Wireless GO II onboard recordings ↗Checked 2026-11-04
- RØDE — Export settings for onboard recordings ↗Checked 2026-11-04
Spotted something out of date? Let Alex know.
How we put our guides together ↗