Practical hardware guide

Connect a keyboard or synth to an interface: line, instrument and stereo

Choose the right interface inputs for a keyboard, synth or guitar without confusing a stereo headphone plug with a balanced mono input.

START HERE

Use line inputs for a keyboard or synth's documented line outputs. Use an instrument input for a pickup signal that requires it. A stereo source usually needs two mono interface inputs; one TRS line socket is not automatically a stereo input.

A correctly leveled mono or stereo recording with the intended channel count.

In this guide
Before you start
  • The source and interface manuals, including output/input labels.
  • Cables matching the source's actual output wiring and the number of channels needed.

Before you change the setup

Musical equipment can use similar quarter-inch connectors for different signals. A guitar pickup, a synthesizer line output and a stereo headphone output are not interchangeable just because the plug fits. The receiving input must be appropriate for the source level and wiring.

Focusrite's guidance distinguishes mic, line and instrument inputs and notes that its balanced TRS line inputs carry mono signals. A keyboard's left and right line outputs therefore normally need separate inputs for stereo. An interface with one microphone input and one line/instrument input is not the same as a pair of line inputs for a stereo keyboard.

Run a controlled check

  1. Identify the source output

    Read the keyboard or synth's labels and manual. Decide whether you will use separate left/right line outputs, a documented mono output or a headphone output requiring a suitable breakout. Exclude speaker-level amplifier outputs.

    Look for: The cable plan starts with the signal actually produced, not the connector you happen to have available.

  2. Count usable receiving inputs

    Check which interface channels accept line level and whether any share a connector with another function. Reserve two suitable channels for stereo, or deliberately choose mono if the source documents that option.

    Look for: The interface has the right number and type of inputs before software routing is considered.

  3. Choose the input mode

    Select line for a line-level keyboard/synth output. Select instrument only for a source that requires the instrument input. Keep input gain conservative while establishing sound, then adjust using the source's documented operating level.

    Look for: The input is not overloaded or unnecessarily weakened by an unsuitable mode.

  4. Test each channel separately

    Record a recognizable left/right test from the source if available, or deliberately play with one output connected at a time at low monitoring level. Label the software channels and verify the saved file.

    Look for: You know which physical output reaches each recording channel and can spot missing or swapped sides.

  5. Build the stream mix deliberately

    Choose whether viewers need stereo music, a mono instrument feed or separate tracks for editing. Add the vocal microphone afterward and check the combined level with a short rehearsal.

    Look for: The final mix reflects the intended presentation rather than accidental panning caused by input numbering.

Read the result and keep a working setup

If a stereo headphone signal is fed directly into one balanced mono input through a simple TRS cable, the result can be weak or strange because the input is not expecting left and right channels in that wiring. Use the source manufacturer's appropriate stereo-to-two-mono connection, or its dedicated line outputs, instead of compensating with extreme gain.

If distortion remains even at low interface gain, recheck the output type and source level. Turning down a software fader after the interface does not establish that the analog input is clean. Likewise, a quiet keyboard is not a reason to switch randomly between mic, line and instrument connections.

Finish by naming the cables and input pair in the session notes. This is especially useful on a desk shared with gaming equipment, where a familiar socket may be repurposed between sessions. Your useful compatibility result is the source mode, cable wiring, interface mode and recording-channel map together.

Keep these distinctions clear

Keep these distinctions clear
SourceInput plan
Keyboard/synth line outputsAppropriate line inputs; usually two for stereo.
Passive pickup signalDocumented instrument input.
Stereo headphone outputCorrect breakout to suitable inputs.
Power-amplifier speaker outputDo not connect to ordinary interface inputs.

Try it on your own setup

Start small: try the free files or continue with a guide for the part you’re working on.

Choose an Audio Interface for Your PC and Console Connections ↗

Sources & references

Documentation review checked 4 November 2026 using the primary sources listed below. This is not a hands-on product test: the diagnostic sequence and rehearsal suggestions are Foxdip editorial guidance. No measured performance, search volume, price or universal compatibility result is claimed.

  1. Focusrite — Mic, line and instrument level ↗Checked 2026-11-04
  2. Scarlett Solo 3rd Gen — Hardware features ↗Checked 2026-11-04

Spotted something out of date? Let Alex know.

How we put our guides together ↗
READ NEXT

A few places to go from here.

All stories

Choose an Audio Interface for Your PC and Console Connections

Compare a PC-only interface, extra analog line inputs and a documented PS5 USB route without assuming USB-C means console support.

One Microphone or Two for a Two-Person Stream?

Plan a shared desk conversation, two separate microphones and the interface channels and headphone feeds that make each arrangement manageable.